Immunoglobulin light chain amyloidosis diagnosis and treatment algorithm 2021

Immunoglobulin light chain amyloidosis (AL) commonly presents with nephrotic range proteinuria, heart failure with preserved ejection fraction, nondiabetic peripheral neuropathy, unexplained hepatomegaly or diarrhea, and should be considered in patients presenting with these symptoms. More importantly, patients being monitored for smoldering multiple myeloma and a monoclonal gammopathy of undetermined significance (MGUS) are at risk for developing AL amyloidosis. MGUS and myeloma patients that have atypical features, including unexplained weight loss; lower extremity edema, early satiety, and dyspnea on exertion should be considered at risk for light chain amyloidosis. Overlooking the diagnosis of light chain amyloidosis leading to therapy delay is common, and it represents an error of diagnostic consideration. Herein we provide a review of established and investigational treatments for patients with AL amyloidosis and provide algorithms for workup and management of these patients.Subject terms: Myeloma, Chemotherapy     

Effectiveness,Patient Satisfaction,and Cost Reduction of Virtual Joint Replacement Clinic Follow-Up of Hip and Knee Arthroplasty

BackgroundTotal hip and knee arthroplasties are increasingly performed operations, and routine follow-up places huge demands on orthopedic services. This study investigates the effectiveness, patients’ satisfaction, and cost reduction of Virtual Joint Replacement Clinic (VJRC) follow-up of total hip arthroplasty and total knee arthroplasty patients in a university hospital. VJRC is especially valuable when in-person appointments are not advised or feasible such as during the COVID-19 pandemic.MethodsA total of 1749 patients who were invited for VJRC follow-up for knee or hip arthroplasty from January 2017 to December 2018 were included in this retrospective study. Patients were referred to VJRC after their 6-week postoperative review. Routine VJRC postoperative review was undertaken at 1 and 7 years and then 3-yearly thereafter. We evaluated the VJRC patient response rate, acceptability, and outcome. Patient satisfaction was measured in a subgroup of patients using a satisfaction survey. VJRC costs were calculated compared to face-to-face follow-up.ResultsThe VJRC had a 92.05% overall response rate. Only 7.22% required further in-person appointments with only 3% being reviewed by an orthopedic consultant. VJRC resulted in an estimated saving of £42,644 per year at our institution. The patients’ satisfaction survey showed that 89.29% of the patients were either satisfied or very satisfied with VJRC follow-up.ConclusionVJRC follow-up for hip and knee arthroplasty patients is an effective alternative to in-person clinic assessment which is accepted by patients, has high patient satisfaction, and can reduce the cost to both health services and patients.     

Defining the dimensions of circulating tumor cells in a large series of breast,prostate, colon,and bladder cancer patients

Circulating tumor cells (CTCs) in the blood of cancer patients are of high clinical relevance. Since detection and isolation of CTCs often rely on cell dimensions, knowledge of their size is key. We analyzed the median CTC size in a large cohort of breast (BC), prostate (PC), colorectal (CRC), and bladder (BLC) cancer patients. Images of patient‐derived CTCs acquired on cartridges of the FDA‐cleared CellSearch^® method were retrospectively collected and automatically re‐analyzed using the accept software package. The median CTC diameter (μm) was computed per tumor type. The size differences between the different tumor types and references (tumor cell lines and leukocytes) were nonparametrically tested. A total of 1962 CellSearch^® cartridges containing 71 612 CTCs were included. In BC, the median computed diameter (CD) of patient‐derived CTCs was 12.4 μm vs 18.4 μm for cultured cell line cells. For PC, CDs were 10.3 μm for CTCs vs 20.7 μm for cultured cell line cells. CDs for CTCs of CRC and BLC were 7.5 μm and 8.6 μm, respectively. Finally, leukocytes were 9.4 μm. CTC size differed statistically significantly between the four tumor types and between CTCs and the reference data. CTC size differences between tumor types are striking and CTCs are smaller than cell line tumor cells, whose size is often used as reference when developing CTC analysis methods. Based on our data, we suggest that the size of CTCs matters and should be kept in mind when designing and optimizing size‐based isolation methods.

Abbreviations

ACCEPT

Automated CTC Classification, Enumeration, and PhenoTyping software

BC

breast cancer

BLC

bladder cancer

CD

computed diameter

CEL

cultured tumor cell (cell line)

CK

cytokeratin

CRC

colorectal cancer

CTC‐L

circulating tumor cells derived from cerebrospinal fluid (liquor)

CTCs

circulating tumor cells

DAPI

4′6‐diamidino‐2‐phenylindole

EMT

epithelial–mesenchymal transition

EpCAM

epithelial cell adhesion molecule

IQR

interquartile range

KW test

Kruskal–Wallis test

MWU test

Mann–Whitney U test

NCR

nucleus/cytoplasm ratio

P2A

perimeter to area

PC

prostate cancer

TIF

tagged Image Format files

TXT

text file

μm

micrometer

µm²

square micrometers

     

Selective Laser Melting of Al-Based Matrix Composites with Al2O3 Reinforcement: Features and Advantages

Aluminum matrix composites (AMC) are of great interest and importance as high-performance materials with enhanced mechanical properties. Al₂O₃ is a commonly used reinforcement in AMCs fabricated by means of various technological methods, including casting and sintering. Selective laser melting (SLM) is a suitable modern method of the fabrication of net-shape fully dense parts from AMC with alumina. The main results, achievements, and difficulties of SLM applied to AMCs with alumina are discussed in this review and compared with conventional methods. It was shown that the initial powder preparation, namely the particle size distribution, sphericity, and thorough mixing, affected the final microstructure and properties of SLMed materials drastically. The distribution of reinforcing particles tends to consolidate the near-melting pool-edges process because of pushing by the liquid–solid interface during the solidification process that is a common problem of various fabrication methods. The achievement of an homogeneous distribution was shown to be possible through both the thorough mixing of the initial powders and the precise optimization of SLM parameters. The strength of the AMCs fabricated by the SLM method was relatively low compared with materials produced by conventional methods, while for superior relative densities of more than 99%, hardness and tribological properties were obtained, making SLM a promising method for the Al-based matrix composites with Al₂O₃.